这是一个创建于 1185 天前的主题，其中的信息可能已经有所发展或是发生改变。
家里有两个 N1 盒子，都是 armbian 系统，有一个不带桌面，另外一个带桌面，先用的不带桌面的，用的挺好，一高兴又买了一个，装了个带桌面的 armbian，都用无线和路由器连接，两个的 IP 我都是设置的静态 IP 而且不一样，现在的问题是，带桌面的单独开机后，在路由器里显示的和不带桌面的显示一样，而且 mac 地址显示的也一样，但是我用 ifconfig 查询带桌面的这台 N1,mac 地址实际上和第一台是不一样的，问题出在哪里，N1 配置？路由器配置（用的 tplink ）？
我贴一下带桌面这台 N1 的 interface 文件
# be done in an anachronistic way:
#
#allow-hotplug wlan0
auto wlan0
iface wlan0 inet static
address 192.168.0.116
netmask 255.255.255.0
gateway 192.168.0.1
dns-nameservers 8.8.8.8 114.114.114.114
# wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf
# Disable power saving on compatible chipsets (prevents SSH/connection dropouts over WiFi)
#wireless-mode Managed
#wireless-power off
# Local loopback
auto lo
iface lo inet loopback
同时查一下 ifconfig
root@aml:/etc/network# ifconfig
eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether fc:7c:02:8f:ee:12 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 20
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 4 bytes 156 (156.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 4 bytes 156 (156.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.0.122 netmask 255.255.255.0 broadcast 192.168.0.255
inet6 fe80::ca13:fe6c:bef:9a52 prefixlen 64 scopeid 0x20<link>
ether b8:27:eb:74:f2:6c txqueuelen 1000 (Ethernet)
RX packets 47791 bytes 4998248 (4.7 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 24953 bytes 9910432 (9.4 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
但在 tplink 界面里这台显示的是这个，这个和那个不带界面的单独启动显示的一样？（两台还没有同时开过）
IP：192.168.0.122 | MAC：B8-27-EB-74-F2-6C | 5G 无线连接
我贴一下带桌面这台 N1 的 interface 文件
# be done in an anachronistic way:
#
#allow-hotplug wlan0
auto wlan0
iface wlan0 inet static
address 192.168.0.116
netmask 255.255.255.0
gateway 192.168.0.1
dns-nameservers 8.8.8.8 114.114.114.114
# wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf
# Disable power saving on compatible chipsets (prevents SSH/connection dropouts over WiFi)
#wireless-mode Managed
#wireless-power off
# Local loopback
auto lo
iface lo inet loopback
同时查一下 ifconfig
root@aml:/etc/network# ifconfig
eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether fc:7c:02:8f:ee:12 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 20
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 4 bytes 156 (156.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 4 bytes 156 (156.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.0.122 netmask 255.255.255.0 broadcast 192.168.0.255
inet6 fe80::ca13:fe6c:bef:9a52 prefixlen 64 scopeid 0x20<link>
ether b8:27:eb:74:f2:6c txqueuelen 1000 (Ethernet)
RX packets 47791 bytes 4998248 (4.7 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 24953 bytes 9910432 (9.4 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
但在 tplink 界面里这台显示的是这个，这个和那个不带界面的单独启动显示的一样？（两台还没有同时开过）
IP：192.168.0.122 | MAC：B8-27-EB-74-F2-6C | 5G 无线连接
 |
1
minami 2021-08-27 23:23:58 +08:00  1
N1 刷 armbian 的话，MAC 都会变成 b8-27-eb-74-f2-6c 这个。恩山上有修复教程贴
|
 |
2
gatusokaka OP @minami 嗯，已经有了可以了
|
Select Language